3/12/2024 0 Comments 2005 mustang shift knobThe Genesis Coupe arrived in United States dealerships on February 26, 2009, as a 2010 model. It is Hyundai's first rear-wheel drive sports coupe, and shares its basic platform with the Hyundai Genesis luxury sedan. Allow appropriate time for Loctite™ type adhesive to secure shift knob before using.The Hyundai Genesis Coupe is a rear-wheel drive sports coupe from Hyundai Motor Company, first released on October 13, 2008, for the Korean market. Turn knob counter-clockwise until graphics are in desired position and the Reverse Lockout mechanism can be fully engaged and is functional.Ħ. Install Shift Knob by threading clockwise onto shifter shaft.ĥ. We recommend using a Loctite™ type adhesive that is NOT permanent so that the shift knob will not be damaged if future removal is necessary.ģ. Apply a small amount of Loctite™ type adhesive to shifter threads. Clean all threads prior to installation.Ģ. Shift Knob with Recessed Threads for Reverse Lock Out Installation Instructions:ġ. Turn Jam Nut counter-clockwise until it is tight against bottom of shift knob.Ĭontact Speed Dawg LLC with any technical questions toll free 86 or 71. Turn knob counter-clockwise until graphics are in desired position.Ħ. Install Shift Knob onto shifter until it becomes snug.ĥ. Thread Jam Nut onto shifter until at least 1/2" of threads are visible above Jam Nut.Ĥ. Determine correct Shift Knob and Jam Nut thread size.ģ. Shift Knob Installation Instructions with Jam Nut:ġ. Turn Boot Retainer counter-clockwise until it is tight against bottom of Shift Knob.ĭO NOT ALLOW SHIFT KNOB TO "BOTTOM OUT" ON SHIFTER SHAFT.Ĭontact Speed Dawg LLC with any technical questions toll free 1-86 or 71. Turn knob counter-clockwise until graphics are in desired position.ħ. DAMAGE COULD RESULT WHICH WILL CAUSE THE SHIFT KNOB TO RATTLE OR BREAK.Ħ. Install Shift Knob onto Adapter until it becomes snug.ĬAUTION - DO NOT OVER-TIGHTEN. Thread Brass Adapter Insert onto shifter until it touches the Boot Retainer.ĥ. Thread Boot Retainer onto shifter leaving approximately 1/2” of threads visible above Boot Retainer.Ĥ. Clean all threads prior to installation.ģ. Determine correct Threaded Brass Adapter Insert and Retainer thread size.Ģ. Shift Knob Adapter Installation Instructions with Mustang (2005-2014) Boot Retainer:ġ. WARNING: DO NOT ALLOW SHIFT KNOB TO "BOTTOM OUT" ON SHIFTER SHAFT.ĭAMAGE COULD RESULT WHICH IS NOT COVERED BY WARRANTY.Ĭontact Speed Dawg LLC with any technical questions toll free 1-86 or 1-71. Turn Jam Nut counter-clockwise until it is tight against bottom of Adapter. Turn knob counter-clockwise until graphics are in desired positionĨ. Install Shift Knob onto Adapter until it becomes snug.ħ. Thread (brass) Adapter onto shifter until it touches the Jam Nut (or flat washer)Ħ. Place flat washer on shifter above Jam Nut (for smaller shifter diameters only)ĥ. Thread (silver) Jam Nut onto shifter until no more than 3/4" of threads are visible above Jam Nut.Ĥ. Clean all threads prior to installationĬAUTION - DO NOT PUT ADAPTER DIRECTLY INTO SHIFT KNOBģ. Determine correct Adapter and Jam Nut size.Ģ. Shift Knob Installation Instructions with Brass Adapter and Jam Nutġ. THIS COULD CAUSE INTERNAL DAMAGE WHICH COULD CAUSE THE SHIFT KNOB TO RATTLE OR BREAK.ĪLWAYS SECURE SHIFT KNOB USING A JAM NUT OR BOOT RETAINER. WARNING: DO NOT ALLOW SHIFT KNOB TO "BOTTOM OUT" ON SHIFTER SHAFT. INSTALLATION INSTRUCTIONS FOR THREADED GEARSHIFT KNOBS
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |